|
WRAS
Approved Water Fittings
|
Listing Number
0803102 |
Print
this entry |
|
`CHP18` break cistern with a stainless steel body incorporating Type `AB` air gap arrangement. Inlet incorporates a solenoid valve (AUK Muller GmbH) which is connected to a float switch (AUK Muller GmbH) that controls the flow. Assembly also incorporates two brass/copper condensers (Hobart). For use with the CNR range of dishwashers. Maximum supply pressure 16.0 bar. |
|
Size: ¾" BSP inlet. |
|
Model: CHP18 break cistern. |
|
Marking: Model number, Hobart and product information printed on adhesive label on body. |
|
Installation Requirements :
R001
|
|
Note: |
|
Proviso: |
|
Manufacturer: Hobart Maschinen GmbH |
List all fittings by this
manufacturer |
|
Factor: Hobart UK |
List all fittings by this factor |
|
Listing Number
0809031 |
Print
this entry |
|
`Poly A30` cold water storage cisterns incorporating an `AB` air gap. The unit comprises a close fitting (snap type) lid, screened warning pipe/overflow pipe, insulating jacket to protect against heat or frost and a factory fitted bent inlet valve lever arm designed to be used with the unit.
|
|
Size: 15mm BSP.
|
|
Model: Poly A30, Type 'AB' air gap.
|
|
Marking: 'Polytank', product designation and product information moulded onto body.
'Polytank' and product information printed on adhesive label on chamber lid.
|
|
Installation Requirements :
R001 R270 R280
|
|
Note: |
|
Proviso: The fitting shall be installed using the lever arm provided by the manufacturer connected to a float operated valve conforming to BS1212: Part 2.
|
|
Manufacturer: Polytank Group Ltd |
List all fittings by this
manufacturer |
|
Factor: |
List all fittings by this factor |
|
Listing Number
0606088 |
Print
this entry |
|
SC, M, EN, Low and GRP horizontal split ranges of rectangular glass reinforced polyester cold-water storage cisterns and lids. Joints of the split tanks are sealed with mastic sealing tape and secured with stainless steel fixings. Units can be factory pre-insulated (with provision for the fixture of fittings) or non-insulated supplied with insulating jackets to protect from heat and frost. Supplied with screened vent, screened overflow, grommet pipe fitting and screened warning pipes. The storage cisterns are supplied with an `AB` air gap, which is shrouded (screened). The dimensions are based on the inlet supply dimensions as follows:
Inlet Pipe Size Weir Width Weir Height
Up to 22mm 200 67
23 - 42 350 120
43 - 54 450 151
55 - 76 600 209
88 - 108 800 291
109 - 133 900 358 |
|
Size: SC maximum capacity 4540 (litres) 1000 (gallons)
M maximum capacity 6810 (litres) 1500 (gallons)
EN maximum capacity 8000 (litres) 1760 (gallons)
Low maximum capacity 3451 (litres) 760 (gallons)
GRP horizontal split maximum capacity 8000 (litres) 1760 (gallons). |
|
Model: SC, M, EN, Low and GRP horizontal split incorporating (AB air gap) ranges.
|
|
Marking: Manufacturer's name, address, product reference and capacity printed on adhesive label. Pre-insulated `Sarena` tanks printed on outer panel. |
|
Installation Requirements :
R001 R270 R280
|
|
Note: |
|
Proviso: |
|
Manufacturer: Sarena MFG Ltd |
List all fittings by this
manufacturer |
|
Factor: |
List all fittings by this factor |
 |