 |
|
WRAS
Approved Materials
|
Coatings, Paints & Linings |
Section 5042 |
|
Site applied pipe and fittings coatings |
|
Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing.
Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.
|
|
WRAS
Approval Number 1111534 |
|
|
Interline 925 (White), 2 part solvent free epoxy coating consisting of base (white - THA125) and curing agent (white - THA 127). Interline 925 (Grey), 2 part solvent free epoxy coating consisting of base (white - THA133) and curing agent (white - THA 134). Mix and apply as per manufacturer`s instructions. Cure for 7 days at 25°C. For use with water up to 23°C. (Manufactured in India) |
|
Supplier: International Protective Coatings |
|
WRAS
Approval Number 1212504 |
|
|
Corroline PWSF 100 (Grey/Blue). Site applied, light grey coloured, two part epoxy based coating, consisting of a white coloured base (liquid form) and dark grey coloured activator (paste form). Mix base and activator in a 2:1 volume ratio. Cure for 7 days at 20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
|
|
Supplier: Corrotech Construction Chemicals (MCT Group) |
|
WRAS
Approval Number 1207547 |
|
|
Epicol Solvent Free Epoxy Cream, Blue & Red. Site applied, two part (consisting of base & hardener), solvent free epoxy coating. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.
|
|
Supplier: Spencer Coatings Ltd |
|
WRAS
Approval Number 1301541 |
|
|
Resichem 507 DWPU Brush Grade. Site applied, blue coloured, two part polyurethane coating, consisting of a base and activator. Mix based and activator in a ratio of 3.24:1 by weight. Cure for 14 days at 7°C. For use with water up to 23°C.
|
|
Supplier: Resimac Ltd. |
|
WRAS
Approval Number 1301540 |
|
|
Resichem 507 DWPU Spray Grade. Site applied, blue coloured, two part polyurethane coating, consisting of a base and activator. Mix based and activator in a ratio of 3.23:1 by weight. Cure for 14 days at 7°C. For use with water up to 23°C.
|
|
Supplier: Resimac Ltd. |
|
WRAS
Approval Number 1207548 |
|
|
Transpoxy Guard 4.76 Cream, Blue & Red. Site applied, two part (consisting of base & hardener), solvent free epoxy coating. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.
|
|
Supplier: Transocean Coatings |
|
WRAS
Approval Number 1208505 |
|
|
Interline 925 White, 2 part solvent free epoxy coating consisting of base (white - THA 170) and curing agent (grey - THA 171). Interline 925 Grey, 2 part solvent free epoxy coating consisting of base (grey - THA 133) and curing agent (grey - THA 134). Mix as per manufacturer`s instructions, apply at a dry film thickness of 500 microns, as well as in line with document: EMEA PC 86 2012. Cure for 7 days at 25°C. For use with water up to 60°C. (Manufactured in India).
|
|
Supplier: International Protective Coatings |
|
WRAS
Approval Number 1301513 |
|
|
Interline 975 (White). Site applied, white coloured, solvent free epoxy coating consisting of a base (Part A) and curing agent (Part B). Mix the two parts in a ratio of 3.05:1 by weight. Cure for 21 days at 7°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
|
|
Supplier: International Protective Coatings |
|
WRAS
Approval Number 1301554 |
|
|
Acothane Blue (blue coloured) and Acothane Cream (cream coloured), two pack, solvent free coatings to be used in conjunction with Acothane LV, a two pack, solvent free, polyurethane sealer. Both the coating and sealer are to be mixed and applied as per manufacturer`s instructions.
Acothane DW instructions have reference 06ADW, issue 1 dated July 2012.
Acothane LV instructions have reference 06ALVS (A10), issue 3 dated November 2009. Acothane LV Sealer to be applied and then cured for 48 hours at 3°C.
Acothane DW to be applied on top of sealer and then cured for 7 days at 3°C.
For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
|
|
Supplier: Spencer Coatings Ltd |
|
WRAS
Approval Number 1201507 |
|
|
ePIPE® UK. Reddish-Brown coloured, two part epoxy coating. Mix and apply as per manufacturer`s instructions. Air cured for 60 minutes at 25°C and then water cured for 60 minutes at 60°C. For use with water up to 85°C. |
|
Supplier: Pipe Restoration Technologies, LLC |
|
WRAS
Approval Number 1302533 |
|
|
Interline 925 Black. Black coloured, 2 part solvent free epoxy coating consisting of base (Black liquid, THA172) and curing agent (Brown translucent liquid, THA 173). Mix as per manufacturer`s instructions and apply at a wet film thickness of 750 microns. Cure for 7 days at 25°C. For use with water up to 60°C.
Interline 925 Black. Black coloured, 2 part solvent free epoxy coating consisting of base (Black liquid, THA172) and curing agent (Brown translucent liquid, THA 173). Mix as per manufacturer`s instructions and apply at a wet film thickness of 750 microns. Cure for 7 days at 25°C. For use with water up to 60°C.
`This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval`.
|
|
Supplier: International Paint Ltd. |
|
WRAS
Approval Number 0905515 |
|
|
3M Scothkote Epoxy Coating 162PW grey & 3M Scothkote Epoxy Coating 162PW blue. Two component solvent free epoxy coatings available in blue or grey. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. Cold water use only.
|
|
Supplier: 3M United Kingdom Plc. - Infrastructure Protection Division (IsPD) |
|
WRAS
Approval Number 1006520 |
|
|
Belzona 1391 (Ceramic HT). Dark grey coloured, two part epoxy coating. Mix and apply as per manufacturer`s instructions. Cure for 7 days at 18°C. For use with water up to 85°C.
|
|
Supplier: Belzona Polymerics Ltd |
|
WRAS
Approval Number 1006523 |
|
|
Belzona 5891. Light grey coloured, two part epoxy coating. Mix and apply as per manufacturer`s instructions. Cure for 7 days at 20°C. For use with water up 85°C.
|
|
Supplier: Belzona Polymerics Ltd |
|
WRAS
Approval Number 0912516 |
|
|
Maxepox Flex. Grey coloured, two part epoxy coating. Mix and apply as per manufacturer`s instructions. Cure for 15 days at 20°C. For cold water use only
|
|
Supplier: Drizoro SAU |
|
WRAS
Approval Number 1109512 |
|
|
Titanseal 989. Two part polyurethane coating consisting of a bright blue coloured base & amber coloured hardener. Mix and apply as per manufacturer`s instructions. Cure for 24 hours at an ambient (21-22°C) temperature. For use with water up to 23°C.
|
|
Supplier: Gennor & Company (Chemicals) Ltd |
|
WRAS
Approval Number 1005511 |
|
|
Interline 925 White, 2 part solvent free epoxy coating consisting of base (white - THA 125) and curing agent (grey - THA 127). Interline 925 Cream, 2 part solvent free epoxy coating consisting of base (grey - THA 125) and curing agent (grey - THA 126). Mix and apply as per manufacturer`s instructions.
Cure for 7 days at 25°C. For use with water up to 60°C. |
|
Supplier: International Protective Coatings |
|
WRAS
Approval Number 0904507 |
|
|
Kopatch PC300. Blue/straw coloured, two component, liquid epoxy coating. Mix and apply as per manufacturer`s instructions. Cure 7 days at 25°C. For use with cold water only.
|
|
Supplier: KCC Corporation |
|
WRAS
Approval Number 1201532 |
|
|
Nu Flow System 7000. Red coloured, two-part epoxy resin coating consisting of Part A (red) and Part B (amber). Mix and apply as per manufacturer`s instructions. Cure for 1 hour at 38°C and then for a further 24 hours at 22°C. For use with water up to 60°C.
|
|
Supplier: Nu Flow Technologies |
|
WRAS
Approval Number 1109538 |
|
|
Versathane. Two part polyurethane coating consisting of a bright blue coloured base & amber coloured hardener. Mix and apply as per manufacturer`s instructions. Cure for 24 hours at an ambient (21-22°C) temperature. For use with water up to 23°C.
|
|
Supplier: Practical Compounds Ltd. |
|
WRAS
Approval Number 0903524 |
|
|
Sika Permacor 136 TW. Blue coloured, two -part, solvent free epoxy coating. Mix and apply as per manufacturer`s instructions. Cure 7 days at 15°C. For use with hot and cold water up to 40°C.
|
|
Supplier: Sika Services AG |
|
WRAS
Approval Number 0903523 |
|
|
Sikagard-136 DW to be used in conjunction with Sika Icoment 540. Blue coloured, two -part, solvent free epoxy coating (Sikagard-136 DW) intended for use with a two-part, cementitious levelling mortar (Sika Icoment 540). Mix and apply as per manufacturer`s instructions. Cure 7 days at 15°C. For use with hot and cold water up to 40°C.
|
|
Supplier: Sika Services AG |
|
WRAS
Approval Number 0903522 |
|
|
Sikagard-136 DW. Blue coloured, two -part, solvent free epoxy coating. Mix and apply as per manufacturer`s instructions. Cure 7 days at 15°C. For use with hot and cold water up to 40°C.
|
|
Supplier: Sika Services AG |
|
WRAS
Approval Number 0905512 |
|
|
ELC 173/90. Cream coloured two component epoxy resin material designed for the rehabilitation of drinking pipes by centrifugal spray application to the bore of the pipe. Cure for 16 hours at 3°C. Cold water use only.
|
|
Supplier: Subterra |
|
|
|
