Coatings, paints and linings (site applied)

Section 5048

Multi purpose

WRAS Approval Number 1209533

Aquaurathane Extreme, available in black, grey, green and natural (beige) colours. Two part, spray applied polyurea coating, consisting of base and hardener. Mix and apply as per manufacturer`s instructions. Cure for 5 days at 7°C. For use with water up to 23°C.

Supplier: Line-X Protective Coatings Ltd

WRAS Approval Number 1207534

Jazecoat EP 400. Site applied, two part (blue coloured base and straw coloured hardener) epoxy resin coating to be applied in two coats. Mix and apply as per manufacturer`s instructions. Cure coat 1 for 24 hours at 25°C before applying coat 2, and cure for a further 7 days at 25°C. For use with water up to 85°C.

Supplier: J.C.C. (Jazea Construction Chemicals Factory)

WRAS Approval Number 1209535

Aquaurathane Extreme, available in black, grey, green and natural (beige) colours. Two part, spray applied polyurea coating, consisting of base and hardener, for use with Insu-Prime, two part spray applied polyurethane foam primer, consisting of a base and hardener. Mix and apply as per manufacturer`s instructions. The primer should be allowed to set for 10 minutes before the top coat is applied. The top coat should be allowed to cure for 5 days at 7°C. For use with water up to 23°C.

Supplier: Line-X Protective Coatings Ltd

WRAS Approval Number 1208501

Epicuro E200-PW. Site applied, two component epoxy resin coating, consisting of a yellow coloured resin and a grey coloured hardener. Mix and apply as per manufacturer`s instructions. Cure for 7 days at 7°C. For use with water up to 40°C.

Supplier: Epicuro Ltd

WRAS Approval Number 1211516

Masterseal® 200 EPS-P. Grey coloured, two part epoxy coating, consisting of base (grey) and reactor (dark grey). Mix and apply as per manufacturer`s instructions. Cure for 14 days at 14°C. For use with water up to 60°C.

Supplier: Saudi BASF For Building Materials Co. Ltd.

WRAS Approval Number 1203529

Corrofill VE. Site applied, two-part (consisting of grey coloured base & clear catalyst) vinyl ester glassflake coating. Mix and apply as per manufacturer`s instructions. Cure for 4 days at 20°C. For use with water up to 23°C.

Supplier: Corrocoat Ltd

WRAS Approval Number 0810540

Masterseal 694. Black coloured, two component, polyuria hot spray coating system consisting of two part epoxy resin and top coat. Mix and apply as per manufacturer`s instructions. For hot and cold water use up to 85°C

Supplier: Saudi BASF For Building Materials Co. Ltd.

WRAS Approval Number 1009556

Masterseal 693. Blue coloured, two component, polyurea coating system consisting of an epoxy base and an epoxy primer. Mix and apply as per manufacturer`s instructions. For use with water up to 85°C.

Supplier: Saudi BASF For Building Materials Co. Ltd.

WRAS Approval Number 1211512

Jazecoat EP 402. Blue coloured, two part (blue coloured base and straw coloured hardener) epoxy resin coating. Mix and apply as per manufacturer`s instructions. Cure coat 1 for 16 hours at 25°C before applying coat 2, and cure for a further 7 days at 25°C. For use with water up to 30°C.

Supplier: J.C.C. (Jazea Construction Chemicals Factory)

WRAS Approval Number 1211513

Jazecoat EPHC. Grey coloured, two part (grey coloured base and clear hardener) epoxy polysulphide coating. Mix and apply as per manufacturer`s instructions. Cure coat 1 for 16 hours at 25°C before applying coat 2, and cure for a further 7 days at 25°C. For use with water up to 30°C.

Supplier: J.C.C. (Jazea Construction Chemicals Factory)

WRAS Approval Number 1302531

Insu-Prime. Site applied, cream coloured, two part polyurea coating. Apply as per manufacturer`s instructions. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval`.

Supplier: Line-X Protective Coatings Ltd

WRAS Approval Number 0810533

3M Scotchkote Urethane Coating 165PW-PR Grey & 3M Scotchkote Urethane Coating 165PW grey, cream & blue. Two component urethane coating (solvent free) Mix and apply as per manufacturer`s instructions. Cure for 7 days at 7°C. Cold water use only. These products may also be factory applied.

Supplier: 3M United Kingdom Plc. - Infrastructure Protection Division (IsPD)

WRAS Approval Number 1004509

EKOPIPE. Red coloured, two part epoxy resin coating. Mix and apply as per manufacturer`s instructions. Cure for 72 hours at 23°C. For use with hot and cold water up to 70°C.

Supplier: EKS Kimya Sanayi Ve Ticaret Ltd. Sti

WRAS Approval Number 1004506

Brushable Ceramic White. Two part, white coloured, ceramic filled epoxy coating consisting of a resin base (white coloured) and hardener (straw coloured). Intended to seal and protect new or repaired surfaces from cavitation, pitting, erosion and wear. Mix and apply as per manufacturer`s instructions. Cure 7 days at 12°C. For use with cold water only.

Supplier: ITW Devcon

WRAS Approval Number 0906534

Eponics WP-NS. Grey coloured, two-part epoxy resin coating consisting of a base and hardener. Mix and apply as per manufacturer`s instructions. Cure for six hours at 30°C. For use with water up to 60°C.

Supplier: Kubota Corporation

WRAS Approval Number 1209534

Line-X XS 350, available in black, grey, green and natural (beige) colours. Two part, spray applied polyurea coating, consisting of base and hardener, for use with Insu-Prime, two part spray applied polyurethane foam primer, consisting of a base and hardener. Mix and apply as per manufacturer`s instructions. The primer should be allowed to set for 10 minutes before the top coat is applied. The top coat should be allowed to cure for 5 days at 7°C. For use with water up to 23°C.

Supplier: Line-X Protective Coatings Ltd

WRAS Approval Number 1209532

Line-X XS 350, available in black, grey, green and natural (beige) colours. Two part, spray applied polyurea coating, consisting of base and hardener. Mix and apply as per manufacturer`s instructions. Cure for 5 days at 7°C. For use with water up to 23°C.

Supplier: Line-X Protective Coatings Ltd

WRAS Approval Number 0910508

Aqua-Pipe PU, two part pipe lining. Mix resin and hardener at a ratio of 100:30, and apply as per manufacturer`s instructions. Cure for 2 hours at 65°C, and cool under pressure for 48 hours. For cold water use only.

Supplier: Sanexen Environmental Services Inc

WRAS Approval Number 0810530

Polyurea hot spray system. Black coloured 2 component coating system consisting of Quick Prime 2 part epoxy resin and Quick Spray Supreme W top coat. Mix and apply as per manufacturers instructions. For hot and cold water use up to 85°C

Supplier: Voelkel Industrie Produkte GmbH