Concrete, Cement and Mortar

Section 5063

Repair materials

High humidity of 80% to 95% is required when curing cementitious materials.

WRAS Approval Number 1302532

Cementitious Coating 851 Grey. Site applied, grey coloured two part, cementitious modified polymer coating, consisting of a white coloured liquid and grey coloured powder. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval`.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 1212500

Concresive 2200. Light grey coloured, two component epoxy bedding compound and adhesive consisting of a base and reactor. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Supplier: BASF Construction Chemicals UAE LLC

WRAS Approval Number 1209504

Monomix. Site applied, grey coloured cementitious repair mortar. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 1209503

Monomix WS. Site applied, grey coloured cementitious repair mortar. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 1203530

Emaco® S188. Grey coloured, cement repair mortar reinforced with synthetic fibres. Mix and apply as per manufacturers` instructions. Cure for 28 days at ambient 20°C - 22°C in moist conditions. For use with water up to 50°C. Emaco® S188. Grey coloured, cement repair mortar reinforced with synthetic fibres. Mix and apply as per manufacturers` instructions. Cure for 28 days at ambient 20°C - 22°C in moist conditions. For use with water up to 50°C.

Supplier: BASF (Hong Kong) Ltd.

WRAS Approval Number 1110530

Cemprotec Elastic Grey. Site applied, two-component cementitious modified, polymer rich coating. Mix Part A (white liquid) with Part B (grey powder) in a ratio of 1:2. Apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 0806526

`Premcrete Hydroseal RX`. Two component, cementitious modified, polymer rich coating. Mix and apply as per manufacturers instructions. Cure 21 days at 7°C. For use with water up to 23°C.

Supplier: Premcrete

WRAS Approval Number 0908531

Renderoc SXtra. Grey coloured, cementitious repair mortar system. Mix and apply as per manufacturer`s instructions. Cure 7 days at 25°C. For use with water up to 50°C.

Supplier: Al Gurg Fosroc LLC

WRAS Approval Number 1004504

Cementitious Coating 851 White. White coloured, cementitious modified polymer coating. Mix and apply as per manufacturer`s instructions. Cure for 7 days at 7°C. For cold water use only.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 1110534

Intercrete 4842 Grey. Site applied, two-component cementitious modified, polymer rich coating. Mix Part A (white liquid) with Part B (grey powder) in a ratio of 1:2. Apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.

Supplier: International Protective Coatings

WRAS Approval Number 1106516

Sika Monotop 612. Grey coloured cementitious, polymer modified, one component repair mortar. Mix and apply as per manufacturer`s instructions. Cure for 21 days at 7°C. For use with water up to 23°C.

Supplier: Sika Hong Kong Ltd

WRAS Approval Number 0812508

Sika Topseal 125. Grey coloured two component polymer modified cementitious waterproofing mortar. Cold water use only.

Supplier: Sika Yapi Kimyasallari AS