Section 1530

Print Entire Section

Miscellaneous Fittings

WRAS Approval Number  1112087

Print this entry

Range of shower adaptors with polysulphone bodies and EPDM `O` rings. SHO ½ MVN & SHO ½ MVR incorporate a self-closing isolation device. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.

Size: ½” male BSP inlet.

Model: SHO ½ MNN, SHO ½ MVN, SHO ½ MNR & SHO ½ MVR.

Marking: Pall, CPC and product information on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Pall Europe Ltd

WRAS Approval Number  1301305

Print this entry

Range of flow sensors with PPS bodies and EPDM O rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C

Size: VVX15: ½” BSP (M), ¾” BSP (M). VVX25: 1”BSP (M), 1 ¼” BSP (M).

Model: VVX15 & VVX25

Marking: Sika and direction of flow arrow on body. Sika, model number and other technical information on electricity hood.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: SIKA Systemtechnik GmbH

WRAS Approval Number  1205358

Print this entry

Brass body quick release coupling with built in isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.

Size: 15mm compression x ½” BSP (F) captive nut.

Model: QRC15

Marking: Manufacturer’s logo on body

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: IDC Group

Factor: TMT Pacific Ireland Ltd

WRAS Approval Number  1203085

Print this entry

JG range of 2, 3 and 4 port DZR brass manifolds incorporating a screw down stop valve at each port. Maximum working pressure 6.0 bar. Maximum operating temperature 80°C.

Size: ¾” (M) BSP inlet, 15mm push fit outlets.

Model: Mana 500 512, Mana 500 513, Mana 500 514.

Marking: `JG` and `+` `-` on operating member.Size and `CR` mark on body.

Installation Requirements : R001           

Note: This meets the requirements of a stop valve.

Proviso:  

Manufacturer: Reliance Water Controls Ltd

Factor:  

WRAS Approval Number  1203059

Print this entry

V range of hydraulic diverter valves (brass) incorporating EPDM diaphragm for use in domestic central heating systems. Maximum working pressure 10.0 bar. Maximum operating temperatures: Primary circuit = 99°C & secondary circuit = 70°C.

Size:  

Model: V35 & V36 (Secondary ½” BSP inlet/outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V37 (Secondary ½” BSP inlet & ½” manifold outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V38 (Secondary ½” BSP inlet ½” female outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V39 (Secondary ½” BSP inlet/outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V41 (Secondary ½” manifold inlet ½” BSP outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V42 (Secondary ½” manifold inlet/outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet). V43 (Secondary ½” manifold inlet/outlet. Primary ¾” BSP inlet/outlet & 1” BSP outlet).

Marking: Gianonni logo and direction of flow arrow on valve body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Giannoni S.p.A

Factor:  

WRAS Approval Number  1201076

Print this entry

Chromium plated brass bodied adaptor incorporating a stainless steel jubilee clip, EPDM `O` rings and seals and a valve which is actuated on assembly of the adaptor. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.

Size: 18mm – 38mm adjustable.

Model: TAPUC.

Marking: Pall, Ideal and size on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Pall Europe Ltd

Factor:  

WRAS Approval Number  1201075

Print this entry

Range of in line adaptors with chromium plated brass body incorporating EPDM seals and `O` rings and a valve which is actuated on assembly of the adaptor. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.

Size: Tap ½ FN ½” non valved. Tap ½ FV ½” valved. Tap ½ MN non valved. Tap ½ MV valved. Tap 22 FN 22mm female thread non valved. Tap 22 FV 22mm female thread valved. Tap 24 MN male thread non valved. Tap 24 MV male thread valved.

Model:  

Marking: C.P.C or Pall on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Pall Europe Ltd

Factor:  

WRAS Approval Number  1201054

Print this entry

Range of electronic bidet seats with flow controlled by a solenoid valve and discharged via a type `AB` airgap. Supplied with non verifiable double check valve assemblies and the inlet incorporates a stainless steel strainer. Maximum working pressures 7.5 bar. Cold water supply only.

Size: ½” BSP inlet.

Model: Bio Bidet BB range: BB-800, BB-900 & BB-1000. IZEN IB range: B7000, IB7100, IB7200, IB7300, IB7500 & IB7500R.

Marking: Biobidet, model and product information on adhesive label on rear.

Installation Requirements : R001           

Note: These appliances incorporate fluid category 5 backflow protection devices.

Proviso:  

Manufacturer: IZEN Co Ltd

Factor: Precision Design Services Ltd

WRAS Approval Number  1206329

Print this entry

`Core` manifold incorporating a single check valve cartridge assembly (suitable for backflow prevention against fluid category 2) and a pre set pressure relief valve (pre set pressure 6.0 bar). Maximum working pressure 16 bar. Cold water use only.

Size: 28 mm compression

Model: CORE 255 003

Marking: RWC, syr, DR and flow arrow on body.RWC & 6 bar on cap.

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: Reliance Water Controls Ltd

Factor:  

WRAS Approval Number  1112090

Print this entry

E135 elbow adaptor with chromium plated brass body incorporating and EPDM seal. Maximum operating temperature 70°C.

Size: ½” BSP male x ½” BSP female.

Model: E135.

Marking: Pall on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Pall Europe Ltd

WRAS Approval Number  1205363

Print this entry

Brass body self tapping isolating valve for use with copper pipes. The coupling can be installed in any orientation. Maximum working pressure 10.0 bar. Cold water use only.

Size: 15mm

Model: Aladdin EasyFit Isolator (for 15mm copper pipes)

Marking: Aladdin and Easyfit Isolator on handle

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: NLB Engineering Ltd

Factor:  

WRAS Approval Number  1112057

Print this entry

Range of pressure, flow and temperature sensors. VFS (QT) range of sensors with plastic housing and EPDM `O` rings. VFS range of sensors with plastic housings and EPDM `O` rings. DPS range of sensors with plastic housings incorporating EPDM seals with stainless steel connections. RPS sensors with plastic housing with EPDM `O` rings and stainless steel connections. LPS sensors with plastic housing incorporating EPDM seals. Maximum working pressures LPS and RPS: 30.0 bar DPS P1: 30.0 bar. DPS P2: 10.0 bar. VFS: 16.0 bar. Maximum operating temperatures LPS, RPS, VFS & VFS (QT) - 99°C. DPS - 60°C.

Size: RPS: ½” BSP/NPT. DPS: ¼” female BSP. VFS: ½” to 1½” BSP/NPT. VFS (QT): ¾” to 1¼” BSP/NPSM & ¾” union connection. LPS.

Model: RPS, DPS, VFS, VFS (QT) & LPS

Marking: Direction of flow arrow, Grundfos logo & direct sensors on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Grundfos Sensor A/S

Factor: Grundfos Holdings A/S

WRAS Approval Number  1112047

Print this entry

Range of temperature sensors with brass bodies, T7335CXXX incorporates an EPDM `O` ring. Maximum operating temperature 85°C.

Size: ¼” male BSP.

Model: T7335Axxxx and T7335Cxxxx. xxxx denotes variants in electronic side only.

Marking: Model number and serial number on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Eleprint Srl

Factor: Honeywell Technologies Sarl.

WRAS Approval Number  1112348

Print this entry

Electronic bidet seat with a solenoid valve controlling the flow and discharging via an `AB` air gap. The inlet incorporates a single check valve cartridge. Maximum working pressure 6.8 bar. For use with cold water only.

Size: ½” BSP (M)

Model: SensoWash D-Code 610100 00 2 00 0000 (for UK), 610100 00 2 10 0000 (for Europe) & 610100 00 2 11 0000 (for Switzerland).

Marking: Duravit on lid. Duravit & Sensowash on label.

Installation Requirements : R001           

Note: This appliance incorporates a Fluid category 5 backflow prevention device.

Proviso:  

Manufacturer: Woonglin Coway Co Ltd

Factor: Duravit (China) Sanitaryware Co Ltd

WRAS Approval Number  0907327

Print this entry

`Trentclyde MainsBoost Plus` system, which incorporates a pressure reducing valve adjustable from 0.5 bar to 6 bar (RWC) and on the mains inlet and another pressure reducing valve set at 3 bar (Watts) on the booster pump. Also supplied with double check valve (RWC), single check valves (RWC), pressure relief valve set at 6 bar (Watts), booster pump and a Mains booster vessel (Global Water Solutions). Maximum working pressure & temperature 4 bar & 50°C.

Size: ¾” BSP inlet connections.

Model: Trentclyde MainBoost Plus.

Marking: Label on control box showing manufacturers name, model name, maximum working pressures and temperatures.

Installation Requirements : R001 R420 R530       

Note:  

Proviso:  

Manufacturer: Trentclyde Water Solutions

Factor:  

WRAS Approval Number  1210315

Print this entry

Flow control valve with a cylindrical brass body, stainless steel spring and thermostatic element. Maximum working pressure 10.0 bar & maximum operating temperature 85°C

Size: ½” BSP (M)

Model: Combismart

Marking: Combismart & direction of flow arrow on body

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Save Water Save Money Ltd.

WRAS Approval Number  1209350

Print this entry

Range of water pillows with TPU bodies. Maximum working pressure 0.11 bar. Cold water use only.

Size: 50m3 & 20m3.

Model: Flexitank

Marking: Company logo, MTD, pure water, onsite installations and management use, for potable water capacity, dimensions, maximum height, production code & material code on body.

Installation Requirements : R001 R420         

Note: To be installed where light is excluded, for temporary use only, must be supplied from storage (max head 1.1m)

Proviso:  

Manufacturer: Wiefferink B.V.

Factor:  

WRAS Approval Number  1301064

Print this entry

Range of expansion joints with stainless steel flexible connectors Maximum working pressure 16 Bar. Maximum operating temperature 90°C.

Size: DN50 - DN200

Model: FCS(U)(T)N - 050, FCS(U)(T)N - 065, FCS(U)(T)N - 080, FCS(U)(T)N - 100, FCS(U)(T)N - 125, FCS(U)(T)N - 150, FCS(U)(T)N - 200.

Marking: Model, pipe solutions, web address, size, pressure on the ferrule, tube or flange edge.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Pipe Solutions Ltd.

WRAS Approval Number  1305011

Print this entry

`Non-Freeze` water point for through wall mounting with wall box incorporating a cast gunmetal body with brass rising spindle headworks. The products are supplied with closing key. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Size: ¾” BSP male inlet x ¾” BSP male outlet

Model: YA101 - Non-Freeze water point YA211 = YA101 + Aluminium wall box YA212 = YA101 + Nickel Bronze wall box YA213 = YA101 + Gunmetal Bronze wall box YA304 = YA101 + Grade 304 Stainless steel wall box YA316 = YA101 + Grade 316 Stainless steel wall box

Marking: 'WADE' logo, installation orientation and 'WRAS Approved Product' logo on label on body. 'WADE' logo on front cover of wall box.

Installation Requirements : R001 R040         

Note:  

Proviso:  

Manufacturer:  

Factor: Wade International Ltd

WRAS Approval Number  1112063

Print this entry

Range of pressurisation units with flow controlled by a float operated valve and discharged via type `AB` air gap arrangement. Some models include an automatic dosing system. Inlets incorporate stainless steel strainers, flow restrictors and spherical isolation valves. Maximum working pressure10.0 bar. For cold water use only.

Size: Stainless steel braided EPDM lined flexible hose assembly with 22mm pushfit end connection.

Model: Midi Break - BTMIDI-1. Midi Break - BTMIDI-2A. Midi Fill Digital - MFD-15. Ablution Plant - BTHW-1. Dose and Fill - DF-15.

Marking: Arrow valves logo, model, and product information on front panel.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Arrow Valves Ltd

Factor:  

WRAS Approval Number  1212307

Print this entry

Range of anti-vacuum valves with brass bodies and olives. Not for purposes of backflow prevention. For use within hot water systems to prevent a vacuum within the system. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.

Size: 15mm compression or ¼” BSP (M)

Model: CI-R19000 (15mm) & CI-R19001 (¼”).

Marking: Manufacturer's logo, Calvac, 300 and date of manufacture (MM/YY) on body.

Installation Requirements : R001 R535         

Note:  

Proviso:  

Manufacturer:  

Factor: Altecnic Ltd.

WRAS Approval Number  1304025

Print this entry

Spring loaded, manually operated, water saving device incorporating a polypropylene body and a silicone tube. Cold water use only.

Size: 10mm flexible tube

Model: Mecon Retrofit Variable Flush Mechanism

Marking: Company, instructions on use and contact details on label

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Mecon Water Management Limited

Factor:  

WRAS Approval Number  1303035

Print this entry

Inline spherical valve with brass body and stainless steel ball, which incorporates a drain valve with an EPDM seat. Maximum working pressure 10.0 bar. Cold water use only.

Size: 15mm x ¾” BSP female captive nut

Model: AMVK-15mm (22) comp Warix in-line kit

Marking: MWM and BS2879 on body. BS864-2, size and MWM on compression nut.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: MWM Distributors Ltd

WRAS Approval Number  1303029

Print this entry

Flush-Wiser water saver device for mounting on wc siphons, with adjustable flush volume settings ranging from 0 - 5. Cold water use only.

Size: 7mm

Model: Flush-Wiser

Marking: PHS on Disc

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: PHS Group Plc.

Factor:  

WRAS Approval Number  1303328

Print this entry

Tenant valve assembly consisting of water meter manifold, service valve, pressure reducing valve and double check valve (suitable for backflow prevention up to fluid category 3) within a DZR brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C

Size:  

Model: TVAP 200 075 ¾” BSP (f) TVAP 200 080 1” BSP (f)

Marking: SYR, DR & direction of flow arrow on body. Reliance water controls, - and + on pressure reducing valve.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Hans Sasserath & Co. AG

Factor: Reliance Water Controls Ltd

WRAS Approval Number  1212110

Print this entry

Thermaflow TSL` range of cased and insulated stainless steel unvented primary thermal store cylinders. The stored primary water in the store cylinder is heated directly via immersion heaters or indirectly via stainless steel plate heat exchangers. Heat is transferred from the stored primary water to the secondary water circuit via an internal coil which provides instantaneous hot water. The secondary hot water circuit contains an expansion vessel, single check valve, strainer, flow temperature sensor and a thermostatic mixing valve. The primary thermal store is fitted with flow and return central heating connections. The thermal stores are available with either three (9kW) or four (12kW) 3 kw immersion heaters. The primary thermal storage cylinder is to be filled by the use of a supplied temporary filling loop. A primary expansion vessel is supplied to accommodate the expansion of primary water when heated. An automatic air vent is fitted to the top of the thermal primary store. Maximum working pressure solar circuit = 5.5 bar. Maximum working pressure solid fuel circuit = 5.5 bar. Maximum working pressure of central heating circuit and primary thermal store = 2.5 bar. Maximum working pressure of the secondary water circuit = 2.5 bar.

Size: 210, 250 and 330 Litre primary thermal store capacities

Model: TSL9-210U, TSL9-250U, TSL9-330U, TSL12-210U, TSL12-250U, TSL12-330U.

Marking: Adhesive label on side of cylinder printed with manufacturers name and model number.

Installation Requirements : R001 R140 R360       

Note:  

Proviso:  

Manufacturer: Thermaflow Ltd.

Factor: Thermal Innovations UK Ltd

WRAS Approval Number  1212109

Print this entry

`Thermaflow TH` range of cased and insulated stainless steel unvented primary thermal store cylinders. The stored primary water in the store cylinder is heated directly via immersion heaters or indirectly via stainless steel plate heat exchangers. Heat is transferred from the stored primary water to the secondary water circuit via a stainless steel plate heat exchanger which provides instantaneous hot water. The secondary hot water circuit contains an expansion vessel, single check valve, strainer, flow temperature sensor and a thermostatic mixing valve. The primary thermal store is fitted with flow and return central heating connections. The thermal stores are available with either three (9kW) or four (12kW) 3 kw immersion heaters. The primary thermal storage cylinder is to be filled by the use of the supplied temporary filling loops. A primary expansion vessel is supplied to accommodate the expansion of primary water when heated. An automatic air vent is fitted to the top of the thermal primary store. Maximum working pressure solar circuit = 5.5 bar. Maximum working pressure solid fuel circuit = 2.5 bar. Maximum working pressure of central heating circuit and primary thermal store = 2.5 bar Maximum working pressure of the secondary water circuit = 2.5 bar.

Size: 210, 250, 330 and 450 Litre Primary thermal store capacity

Model: TH9-210U, TH9-250U, TH9-330U, TH12-210U, TH12-250U, TH12-330U and TH12-450U.

Marking: Adhesive label on side of cylinder printed with manufacturers name and model number.

Installation Requirements : R001 R140 R360       

Note:  

Proviso:  

Manufacturer: Thermaflow Ltd.

Factor: Thermal Innovations UK Ltd

WRAS Approval Number  1205331

Print this entry

Shower hose retaining ring with a plastic body.

Size: Wall Mounted

Model: MIRA Cat 5 Hose retaining ring

Marking: Mira Showers on body.

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: Kohler Mira Ltd

Factor:  

WRAS Approval Number  1212311

Print this entry

Spring loaded manual operated flow control valve incorporating plastic body and EPDM gaskets and seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85?C.

Size: ½” BSP (M) and ¾” BSP (M)

Model: 20490358, 20490359 & 20490360

Marking: Open/closed and date clock on body. Model and manufacturing date (WW/YY) on adhesive label.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Elbi International Spa

Factor:  

WRAS Approval Number  1206029

Print this entry

ecoBETA retrofit device with an ABS body for use with siphons to reduce flush volumes.

Size: 10mm Push Fit

Model: ecoBETA Dual flush insert type `siphon`.

Marking: ecoBETA top of clip housing

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: ecoBETA Ltd

Factor:  

WRAS Approval Number  1302325

Print this entry

Bidet toilet seat incorporating an AB air gap supplied via a solenoid valve. Maximum working pressure 10.0 bar. Maximum operating temperature 35?C.

Size: ½” BSP (F) Captive nut

Model: WASHLET EK TCF6402GE (Version without electronic plug for Great Britain).

Marking: TOTO Washlet on casing. Manufacturers name, range name and other information under the seat

Installation Requirements : R001           

Note: This product has a fluid category 5 backflow prevention device built in.

Proviso:  

Manufacturer: TOTO Washlet Techno Co. Ltd.

Factor: TOTO Europe GmbH

WRAS Approval Number  1302027

Print this entry

Range of “Aquamatic” booster sets incorporating vertical or horizontal centrifugal pumps, butterfly valves, lever operated spherical valves, stainless steel transducers & copper or stainless steel manifolds. Maximum working pressure of 10.0 bar = HY(#)AV-ES, BTE(#), AMV(#), AMV(#)-ES, AMF(#) & AMF(#)-ES. Maximum working pressure of 16.0 bar = HY(#)AV & BTE(#)-ES. For cold water use only.

Size: DN40-DN125

Model: HY(#)AV. HY(#)AV-ES. BTE(#). BTE(#)-ES. AMV(#). AMV(#)-ES. AMF(#). AMF(#)-ES. Where (#) denotes the number of pumps that the models may be fitted with: AMV & AMF models = 2, 3 or 4 pumps. AMV-ES & AMF-ES models = 2 or 3 pumps. HYAV & BTE models = 2, 3, 4, 5, 6, 7 or 8 pumps. HYAV-ES & BTE-ES models = 2 or 3 pumps.

Marking: All models: AquaTec Pressmain, model, WRAS and company details on control panel. AMF(#),BTE(#) & HY(#)AV-ES models: AquaMatic Booster Set on control panel.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Aquatech Pressmain Ltd.

Factor:  

WRAS Approval Number  1210081

Print this entry

Pandora District Heat Bank `CPC-150-District 1` cased and insulated stainless steel vented primary thermal store cylinder. The stored primary water in the store cylinder is heated via a stainless steel plate heat exchanger on the central boiler circuit. Heat is transferred from the stored primary water to the secondary water circuit via a stainless steel plate heat exchanger which provides instantaneous hot water. The secondary hot water circuit contains a strainer, flow switch and a thermostatic mixing valve. The primary thermal store is fitted with flow and return central heating connections. A 3 kw immersion is fitted to the primary thermal store. An integral 12 litre vented expansion vessel accommodates the expansion of water when heated. Maximum working pressure central boiler circuit - 6.5 bar. Maximum working pressure of the secondary water circuit - 6 bar.

Size: 157 Litre Primary thermal store capacity

Model: Pandora District Heat Bank, CPC-150-District 1.

Marking: Adhesive label on side of cylinder printed with manufacturers name and model number.

Installation Requirements : R001 R140 R360       

Note: A filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999.

Proviso:  

Manufacturer: Thermal Integration Limited

Factor:  

WRAS Approval Number  1209067

Print this entry

Hand lift type, self-closing dispenser with acetal body. The inlet incorporates a stainless steel strainer. Maximum working pressure 6.0 Bar. For cold water use only

Size: ¾” BSP Female Inlet

Model: SCAT

Marking: `SCAT` & web address on adhesive label on body

Installation Requirements : R001 R040         

Note:  

Proviso:  

Manufacturer: Eurostan Ltd.

Factor:  

WRAS Approval Number  1210324

Print this entry

Range of tank and cistern connectors, with push fittings for use with with copper tube (manufactured to BS EN 1057) PE-X pipe (BS7291-3) & PB pipe (BS7291-2). For cold water use only.

Size: 15mm and 22mm

Model: CM0715S & CM0722S

Marking: JG & size on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: John Guest Ltd

Factor:  

WRAS Approval Number  1209038

Print this entry

Range of regulated circulation valves with brass bodies, EPDM `O` rings and PTFE seals, controlled by a regulating cartridge headwork with dome type operating members, valve incorporates a rising spindle stop valve and drain unit with a rising drain off spindle that allows for a bi-metallic thermometer to be fitted. Maximum working pressure 16.0 Bar. Maximum operating temperature 90°C

Size: ½” - 1” female BSP & ¾” - 1 ¼” male BSP

Model: P603 DN15 FI x FI 30° - 50°, P603 DN20 FI x FI 30° - 50°, P604 DN15 MI x MI 30° - 50°, P604 DN20 MI x MI 30° - 50°, P605 DN15 FI x FI 50° - 60°, P605 DN20 FI x FI 50° - 60°, P605 DN25 FI x FI 50° - 60°, P606 DN15 MI x MI 50° - 60°, P606 DN20 MI x MI 50° - 60° & P606 DN25 MI x MI 50° - 60°

Marking: Size, pressure, Rg, flow arrow, manufacturer's logo on bodies, Temperature setting, Werkseinstellung, pre-set indication arrow on cap.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Rossweiner Armaturen und Messgerate GmbH & Co. OHG

Factor: Pegler Yorkshire Group Ltd

WRAS Approval Number  1206306

Print this entry

Screw down control valve with brass body chromium plated brass ball, PTFE washer and EPDM `O` ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Size: ½” BSP (M)

Model: C04047N009A

Marking: P ½” on body

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Zhejiang Pleast Sanitary Ware Co Ltd

Factor: Hangzhou Doz Import & Export Co Ltd

WRAS Approval Number  0809304

Print this entry

Range of tundishes manufactured from acetal with either a 90° angled fitting or a straight though pattern. The tundishes comply with the requirements of an air break to drain.

Size: ½", 15mm, ¾" or 22mm inlet connection

Model: AP 400001 - ½" (M) x ¾" (F) - Angled.AP 400002 - ¾" (M) x 1"(F) - Angled.AP 400003 - ½" (F) x ¾ (M) - Straight.AP 400004 – 22mm x 1" (F) - Straight.AP 400007 – 15mm x 22mm - Straight.AP 400010 – 15mm x 22mm - Straight.CA 100113 – 15mm x 22mm - Straight.CA 100114 – 22mm x 1"(F) - StraightModel added August 2012: AL400010 15mm x 22mm Straight

Marking: Altecnic on body

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: Altecnic Ltd

Factor:  

WRAS Approval Number  1207072

Print this entry

Range of differential or relative pressure sensors with stainless steel bodies and EPDM O rings. DPI models consist of a sensor and fitting for a capillary tube which is used for measuring the differential pressure between either side of the sensor. Maximum working pressure 28.0 Bar. Maximum operating temperature 85°C

Size: ½” BSP Male inlet (DPI and DPI+T models have 3/8 flare fitting for capillary tube).

Model: DPI V.2, DPI V.2 +T, RPI & RPI +T.

Marking: Grundfos and logo, model, maximum pressure and technical info on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Grundfos Holdings A/S

Factor:  

WRAS Approval Number  1207050

Print this entry

Range of flow sensors with PPS bodies, polypropylene impellors and EPDM O rings. Maximum working pressure 17.5 Bar. Maximum operating temperature 80°C

Size: C7195A2001 – ½”BSP Male inlet/outlet.C7195B1001 – ¾” BSP Male inlet/outlet.C7195C1009 – ¾” O/D.

Model: C7195A2001 – ½”BSP Male inlet/outlet.C7195B1001 – ¾” BSP Male inlet/outlet.C7195C1009 – ¾” O/D.

Marking: Company name, model number, max temp, max pressure and PPS on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Honeywell Technologies Sarl.

Factor:  

WRAS Approval Number  1212325

Print this entry

Proportional modulation valve used to prioritise flow depending on requirement with a brass body and EPDM membrane. Maximum working pressure 10.0 & 6.0 bar. Maximum operating temperature 99°C.

Size: ¾” BSP (M) & ¾” captive nut.

Model: PM - Regler (Art no.10240)

Marking: Meibes, TM, manufacturing date (MM/YY), DVGW 1212 and flow arrow on body

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Meibes System - Technik GmbH

Factor:  

WRAS Approval Number  1107089

Print this entry

Wall mounted heat transfer unit manufactured from copper. The unit allows for the interaction of an open vented primary system heated by solid fuel to an indirect unvented hot water storage cylinder via the cylinders primary coil. The unit is also designed with a solar coil built into it, to allow heat input from a solar circuit. A thermostat is supplied with the unit which controls the circulator on the primary circuit. Maximum working pressure of primary circuit 3 bar. Maximum working pressure of solar coil 3 bar. Maximum operating temperature 80°C.

Size: 22mm copper tube flow and return hot water cylinder connections. 28mm copper tube flow and return solid fuel boiler connections.15mm copper tube flow and return solar circuit connections. 22mm copper tube expansion pipe connection. 15mm copper tube cold feed connection. 15mm copper tube drain connection

Model: `Watawama`.

Marking: A J H Gas and Pipe Fitting Services, address, maximum working pressure and serial number on adhesive label on body.Watawama on inspection panel.

Installation Requirements : R001 R140         

Note:  

Proviso:  

Manufacturer: A J H Gas and Pipe Fitting Services

Factor:  

WRAS Approval Number  1001003

Print this entry

Grey or chromium plated ABS shower inductor incorporating black coloured seals. Minimum operating pressure 0.5 bar. Maximum operating temperature 85°C.

Size: ½" BSP inlet.

Model: Water Widget Water Saving Shower Inductor.

Marking: Challis on body.

Installation Requirements : R001           

Note: Not suitable for use with water efficient shower handsets or low flow and/or electric showers.

Proviso:  

Manufacturer: A L Challis Ltd (T/A Water Controls)

Factor:  

WRAS Approval Number  0812083

Print this entry

`Nova-Flo` bath anti flooding and water saving device valve assembly, with a glass filled PPS housing and EPDM `O` ring.

Size: 22mm BSP pushfit.

Model: Nova-Flo.

Marking: `Nova-Flo` printed on adhesive label on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: About Time Design Ltd

WRAS Approval Number  1011032

Print this entry

Range of bi-metallic flanges with epoxy powder coated steel flanges and gunmetal collars for use with copper tube. For above ground use only. Maximum operating temperature 99°C.

Size: DN – 15, 18, 22, 28, 35, 42, 54, 66.7, 76.1, 108, 133, 159, 219.1.

Model: Type 07 & 05 and Type 02 & 05C.

Marking: Pressure rating, size, model, EN1092-3 AL and product information on flange and collar edge.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Allpex Ltd

Factor:  

WRAS Approval Number  0905800

Print this entry

Range of brass bodied differential bypass valves incorporating a spring loaded adjustment facility. For non-potable water use only.

Size: ¾" BSP, 22mm, 1¼" BSP.

Model: 519500 - ¾" By-Pass 519504 - ¾" By-Pass 519700 - 1¼" By-Pass 519002 GLW - 30 x 1.5 BY-Pass 519003 PMM - 519500 ART - ¾" By-Pass 519500 CON - ¾" By-Pass CONCEPT 519500 GRN - ¾" By-Pass GARANT 519500 TH - ¾" By-Pass 519502 BG - ¾" NPTF By-Pass USA 519502A - ¾" NPTF By-Pass USA 519560 CST - ¾" By-Pass without cap and nut 519700 CON - 1¼" By-Pass CONCEPT.

Marking: Arrow showing direction of flow cast onto body. Manufacturers logo and ± moulded into operating cap.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Caleffi & Co Spa

Factor: Altecnic Ltd.

WRAS Approval Number  1103336

Print this entry

5 Way manifold (DZR brass body) incorporating a single check valve cartridge (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar & maximum operating temperature 85?C.

Size: 1” BSP inlet (F), 2 x ¾” BSP (F) and 2 x 1” BSP (F) outlets.

Model: Al 100106 Unvented Manifold.

Marking: Altecnic and flow arrow on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Airaga Rubinetterie Spa

Factor: Altecnic Ltd.

WRAS Approval Number  0902096

Print this entry

`Alumasc Dispense` glass rinser, incorporating a self-closing headwork, pressure reducing valve and double check valve (Barberi). Maximum inlet pressure 16.0 bar.

Size: ½" BSP.

Model: Alumasc Dispense ADI-001.

Marking: `Alumasc Dispense Ltd` printed on adhesive label on support arm.

Installation Requirements : R001           

Note: Discharge to drain must be via a Type `AA`, `AB` or `AD` air gap or in accordance with EN1717.

Proviso:  

Manufacturer: Alumasc Dispense Ltd.

Factor:  

WRAS Approval Number  1012700

Print this entry

Range of anti siphon nozzles (air break to drain) for use with laboratory taps, manufactured from brass with a grey epoxy powder coating. Maximum operating temperature 48°C.

Size: ½” BSP female inlet, 15mm spigot outlet.

Model: 800100.

Marking: Company logo and AB on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Carlos Arboles SA.

Factor: Arboles UK Ltd.

WRAS Approval Number  1012801

Print this entry

Range of unmeasured flow reducers designed for use with water meters and consisting of an acetal cartridge insert in either a brass or plastic body. The valve regulates the water flow at times of low flow rates which are not registered by the water meter, allowing low flow rates to be measured. Maximum working pressure 16.0 bar and cold water use.

Size: Plastic Casing: ½"x ½" ; ¾"x ¾" & 1"x 1" Brass Casing: ¾"(M) x 1" Captive Nut , ½"x ¾"Captive Nut , ½"(M) x ½"(F), ¾"(M) X ¾" (F), 1"(M) X 1"(F) ¾"(F) X ¾" (F) & 1"(F) X 1"(F)

Model: Plastic Casing: 0577-50BPF, 0577-34BPF-34BPF & 0577-1BPF-1BPF. Brass Casing: 0587-01U34MBR-1T4R, 0587-34U12MBR-1T4R, 0587-12BF12BM, 0587-34BF34BM, 0587-01BF01BM, 0587-34F34FB & 0587-01F01FB

Marking: ARI, company logo, direction of flow arrow, PN16 & size on brass casing on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: ARI Flow Control Accessories

Factor:  

WRAS Approval Number  1011005

Print this entry

Lever operated spherical valve assembly with a brushed chrome and cast brass body, EPDM O-rings and PTFE seat. The assembly incorporates a stainless steel strainer and temperature sensor. The outlet incorporates a single check valve cartridge (suitable for backflow protection against fluid category 2). Maximum working pressure 8 bar & maximum operating temperature 95°C.

Size: Inlet – ¾” male BSP. Outlet – 22mm compression.

Model: Ball valve 374 / Strainer 594.

Marking: Model number, size and Product Information on ball valve body and lever.Model number ‘LK’, direction of flow arrow on filter body.‘LK’ on elbow connection.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: ARJO Hospital Equipment AB

Factor:  

WRAS Approval Number  1011006

Print this entry

`Shower Splitter` with brass body and EPDM O-rings. The assembly incorporates a temperature sensor and `JG` push-fit connectors. Maximum working pressure 8.0 bar & maximum operating temperature 50°C.

Size: 12mm pushfit inlets, 15mm spigot outlet.

Model: Shower splitter – 58215.

Marking: Arjo and model number on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Arjo Hospital Equipment AB

Factor:  

WRAS Approval Number  1011007

Print this entry

Bleeder T Type with plastic body, EPDM O-rings and John Guest push fit fittings on the inlets. For use with either copper or PEX tube. Maximum working pressure 8.0 bar at 50°C.

Size: 12mm pushfit fittings, 6mm spigot connection.

Model: Bleeder T Type 8258197

Marking: 8258197 and Product Information on body.8258197 PP on spigot connection.Size on push-fit insert.

Installation Requirements : R001           

Note:  

Proviso: To be installed where light is excluded.

Manufacturer: Arjo Hospital Equipment AB

Factor:  

WRAS Approval Number  1006035

Print this entry

Air break to drain with chromium plated cast brass body and EPDM seal.

Size: ½” BSP male inlet / 10mm spigot outlet.

Model: S9854AA - G½”.

Marking: AS etched into body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: American Standard (Jiangmen) Fitting Co Ltd

Factor: Armitage Shanks

WRAS Approval Number  1102056

Print this entry

`Trevi` shower elbow with chromium plated ABS body and brass inlet with an EPDM `O` ring. Maximum working pressure 10.0 bar & maximum operating temperature 85°C

Size: ½” BSP male inlet.

Model: E4705AA – Trevi shower elbow.

Marking: ISI on body.

Installation Requirements : R001 R040         

Note:  

Proviso:  

Manufacturer: Bossini Spa

Factor: Armitage Shanks

WRAS Approval Number  1112062

Print this entry

Range of pressurisation units with flow controlled by solenoid valves and discharged via type `AB` air gap arrangement. Some models include an automatic dosing system. Inlets incorporate stainless steel strainers, flow restrictors and spherical isolation valves. Maximum working pressure 10.0 bar. For cold water use only.

Size: Stainless steel braided EPDM lined flexible hose assembly with 22mm pushfit end connection.

Model: Midi Break - BTMIDI - 3A. Midi Fill Digital - MFD22. Dose and Fill - DF22.

Marking: Arrow valves logo, model, and product information on front panel.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Arrow Valves Ltd

Factor:  

WRAS Approval Number  1105057

Print this entry

Range of district heating units consisting of a heat exchanger, flow sensors, pumps and EPDM gaskets or `O` rings. Inlet incorporates a strainer. Maximum working pressure 8.0 bar (secondary), 4 bar (primary) & maximum operating temperature 60°C.

Size: 1” BSP male inlet.

Model: Sirius SAT RS2Z, Sirius SAT RS & Sirius SAT RSP.

Marking: Potterton Commercial, model and technical information on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Baxi SpA

Factor:  

WRAS Approval Number  1007313

Print this entry

Range of hose assemblies with chromium plated metal outer casing. For use with shower handsets. Supplied with NBR washer and stainless steel strainer.

Size: ½" BSP (F) connections.

Model: H11029, H31028,H15256 & H150256

Marking: Bristan etched into ½" BSP (F) connection.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Jomoo Group Co, Ltd

Factor: Bristan Group Limited

WRAS Approval Number  1107008

Print this entry

Range of butterfly wastes with a brass bodies and plug sealed with an EPDM gasket. Supplied with metal backnuts.

Size: 1½” BSP male.

Model: RARE WST FLIP1C & RARE WST FLIP2C

Marking: BGLI and year and month of manufacture on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Taizhou Idcvoda Valve Co Ltd

Factor: Bristan Group Limited

WRAS Approval Number  1007314

Print this entry

PVC lined hose assembly with white coloured outer casing. For use with shower handsets. Supplied with NBR washer and stainless steel strainer.

Size: ½" BSP (F) connections.

Model: H111033

Marking: Bristan etched into ½" BSP (F) connection.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: JOMOO GROUP CO, LTD

Factor: Bristan Group Limited

WRAS Approval Number  1107007

Print this entry

Range of square spring push down pop up wastes with a brass bodies and plug sealed with an EPDM gasket. Supplied with metal backnuts.

Size: 1½” BSP male.

Model: RARE WST CLK4C & RARE WST CLK5C.

Marking: BGLI and year and month of manufacture on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Taizhou Idcvoda Valve Co, Ltd

Factor: Bristan Group Limited

WRAS Approval Number  0904018

Print this entry

Range of flow meters with nylon bodies and EPDM `O` rings. Maximum working pressure 8.0 bar. Minimum working pressure 2 bar.

Size: 10-100A inlet 3/8” captive nut, 3/8” BSP outlet & 100-700A inlet ¾” captive nut, ¾” BSP outlet.

Model: Flow meter 10-100A and 100-700A.

Marking: Company name, logo, temperature and working pressure printed onto control panel. Company name, logo and direction of flow arrow moulded onto body.

Installation Requirements : R001           

Note:  

Proviso: For cold water use only.

Manufacturer:  

Factor: Brita GmbH

WRAS Approval Number  1007702

Print this entry

Angled connection fitting with a brass body. Maximum working pressure 6.0 bar.

Size: ½” captive nut & 15mm compression.

Model: Art 15637.

Marking: CR cast onto body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: BRV Bonetti Rubinetterie Valduggia Srl

Factor:  

WRAS Approval Number  1007700

Print this entry

`Caleffi` 5 way manifold incorporating check valve cartridges (Neoperl NV20) (suitable for backflow protection against Fluid Category 2). The manifold incorporates a spigot type connection. Maximum working pressure 10.0 bar.

Size: ¾" BSP inlet, 22mm & 15mm compression outlets.

Model: 300015.

Marking: Caleffi, size and BS 864-2 cast into compression nuts, CR mark cast onto body. Caleffi moulded onto cap.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Caleffi S.p.A

Factor:  

WRAS Approval Number  1103337

Print this entry

Range of water hammer arrestors with brass bodies (brushed chromium plated), incorporating a spring loaded piston with EPDM `O` rings and seals. Maximum working pressure 10.0 bar and maximum operating temperature 90°C.

Size:  

Model: 525040 (½” BSP M), 525130 (3/8” captive nut x 3/8” M) & 525150 (¾” captive nut x ¾” M).

Marking: Caleffi label on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Caleffi S.p.A

Factor:  

WRAS Approval Number  1102333

Print this entry

Flow measurement devices having brass bodies. Maximum working pressure: Hattersley 20.0 bar and Crane 25.0 bar & maximum operating temperature 85 °C.

Size: Hattersley BrandFig 1000 - ½”, ¾”, 1”, 1¼””, 1½” and 2” Fig 1000M - ½” Fig 1000L - ½” Nodel:Crane BrandD901 - ½”, ¾”, 1”, 1¼””, 1½” and 2” D902 - ½”

Model:  

Marking: Hattersley BrandBS 7350, 1000, PN, HNH, size and flow arrow on body. Crane BrandD901, CR, PN, Crane, and flow arrow on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Valvoindustria Ing Rizzio SPA

Factor: Crane Ltd

WRAS Approval Number  1006300

Print this entry

Pressure tapping test points consisting of a brass body and EPDM seal and plug. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C

Size: ¼" BSP (M).

Model: Fig 631 - Hattersley Brand. P84 - Crane Brand.

Marking: Company logo moulded onto the strap.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Crane Fluid & Gas Systems (Suzhou) Co Ltd

Factor: Crane Ltd

WRAS Approval Number  1012045

Print this entry

Range of variable speed electric pump integrated control systems with EPDM `O` rings and encased in a polypropylene housing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.

Size: 1¼” BSP male x 1½” BSP female.

Model: PWM 230 D/9.3PWM 230 I-Basic/8.5PWM 230 3-BasicPWM 400 D/13.3PWM 230 I-Basic/4.3PWM 400 D/7.5

Marking: `DAB`, model number and contact details on top label and `DAB` model number and product information on side label.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: WACS System Srl

Factor: DAB Pumps Spa

WRAS Approval Number  1012046

Print this entry

Range of variable speed electric pump integrated control systems with EPDM `O` rings and encased in a polypropylene housing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.

Size: 1¼” BSP male x 1½” BSP female.

Model: Active Driver M/M 1.1Active Driver M/M 1.5Active Driver M/M 1.8Active Driver M/T 1.0Active Driver M/T 2.2Active Driver T/T 3.0Active Driver T/T 5.5

Marking: `DAB`, model number and contact details on top label and `DAB` model number and product information on side label.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: WACS System Srl

Factor: DAB Pumps Spa

WRAS Approval Number  1106057

Print this entry

DAIKIN `EKHWP 300 A` AND `EKHWP 500A` Polypropylene double walled vented hot water thermal store with hard form insulation between each wall. The thermal store is heated by stainless steel heat exchangers. Heat is transferred from the thermal store to the secondary hot water circuit via a stainless steel heat exchanger which provides instantaneous hot water. Maximum working pressure of domestic hot water heat exchanger 6.0 bar. Maximum working pressure of solar heat exchanger 3.0 bar. Maximum working pressure of primary heat exchanger 3.0 bar. Maximum working temperature of vented primary water 85°C.

Size: 300 litre and 500 litre capacities.

Model: EKHWP 300A (300 Ltr Primary water capacity). EKHWP 500A (500 Ltr Primary water capacity).

Marking: Daikin Europe N.V. capacity, weight, maximum operating temperature, pressure and model on adhesive label on body.

Installation Requirements : R001 R140 R360       

Note:  

Proviso: Compliance with the relevant requirements of the Water Supply (Water Fittings) Regulations 1999 has been assessed for this product only as a component of a heating system. If it is to be installed as part of a system using solar energy or ground- or air- source heat pumps for pre-heating water which is to be used as domestic hot water, the Water Fittings Regulations place a legal duty on the installer and user to ensure that the installation and operation of the complete system prevents contamination of domestic hot water by bacteria such as Legionella, which can grow in water stored at temperatures between 20°C and 45°C Where disinfection by heating is relied on to meet this obligation, information on minimum conditions for thermal disinfection of Legionella bacteria can be found on the WRAS website - www.wras.co.uk

Manufacturer: Rotex Heating Systems GmbH

Factor: Daikin Airconditioning UK Ltd.

WRAS Approval Number  0909040

Print this entry

Range of multi functional thermostatic balancing valves with cast brass bodies and EPDM seals. Maximum working pressure 10 .0 bar

Size: ½" BSP inlet/outlet - MTCV.A - DN15. ¾" BSP inlet/outlet - MTCV.A - DN20.

Model: MTCV.A - DN15. MTCV.A - DN20.

Marking: Direction Arrow, D & size cast into body. `LO8` or `E09` stamped into body. `Danfoss` moulded into cap.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Danfos d.o.o.

Factor: Danfoss A/S

WRAS Approval Number  1001008

Print this entry

`Fig 568` range of air admittance valves with Gunmetal bodies and PTFE seals. The valve is intended to protect drying cylinders, storage cylinders and tanks etc from collapse due to internal vacuum. Maximum working pressure 13.5 bar.

Size: DN15, 20, 25, 32, 40 and 50.

Model: Fig 568 range: N-568-015, N-568-020, N-568-025, N-568-032, N-568-040, N-568-050.

Marking: Nabic 568, size and product code stamped into body

Installation Requirements : R001 R120         

Note:  

Proviso:  

Manufacturer: Delta Fluid Products Ltd

Factor:  

WRAS Approval Number  1009378

Print this entry

Range of axial expansion compensator (expansion bellows), with a stainless steel bellows and internal flow straightener. Maximum working pressure 10.0 bar.

Size: ½" BSP (M) x ½" BSP (M) ¾" BSP (M) x ¾" BSP (M) 1" BSP (M) x 1" BSP (M) 1¼" BSP (M) x 1¼" BSP (M) 1½" BSP (M) x 1½" BSP (M) 2" BSP (M) x 2" BSP (M) 2 ½" BSP (M) x 2½" BSP (M)

Model: DST AX3 - Screwed Axial Bellows AX3/015/MSC (25), AX3/020/MSC (25), AX3/025/MSC (25), AX3/032/MSC (25), AX3/040/MSC (25), AX3/050/MSC (25), AX3/065//MSC (25), AX3/015/MSC (50), AX3/020/MSC (50), AX3/025/MSC (50), AX3/032/MSC (50), AX3/040/MSC (50), AX3/050/MSC (50).

Marking: Body etched AX.

Installation Requirements :             

Note:  

Proviso:  

Manufacturer: DST Group Ltd

Factor:  

WRAS Approval Number  0904040

Print this entry

`Stopmax` flood prevention device which incorporates an acetal pressure regulator and two nylon solenoid valves (RPE Srl). Maximum working pressure 10.0 bar. Cold water use only.

Size: 8mm pushfit inlet.

Model: BSA023 stopmax flood prevention device.

Marking: `Ebac`, stopmax, direction of flow arrow and product info printed on adhesive label on front cover.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Ebac Ltd

Factor:  

WRAS Approval Number  0807070

Print this entry

FRB range of untied and tied rubber bellows with nylon reinforced collar. Maximum working pressure 16.0 bar & maximum operating temperature 99°C.

Size: 32mm - 300mm.

Model: FRB range of untied and tied rubber bellows.

Marking: PN16 & size on body. Size and PN16 on flange.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Elmbridge Pump Company

WRAS Approval Number  1012802

Print this entry

Range of unmeasured flow reducers designed for use with water meters consisting of an acetal cartridge insert in either a brass or plastic body. The valve regulates the water flow at times of low flow rates which are not registered by the water meter, allowing low flow rates to be measured. Maximum working pressure 16.0 bar and cold water use.

Size: Plastic Casing 0577-50BPFLFC-½/4 - ½"x ½". 0577-34BPF-34BPFLFC-½/4 - ¾"x ¾". 0577-1BPF-1BPFLFC-½/4 - 1"x 1". Brass Casing 0587-01U34MBR-1T4RLFC - ¾"(M) x 1" Captive Nut. 0587-34U12MBR-1T4RLFC - ½"x ¾"Captive Nut. 0587-12BF12BMLFC-½/4 - ½"(M) x ½"(F). 0587-34BF34BMLFC-½/4 - ¾"(M) X ¾" (F). 0587-01BF01BMLFC-½/4 - 1"(M) X 1"(F). 0587-34F34FBLFC-½/4 - ¾"(F) X ¾" (F). 0587-01F01FBLFC-½/4 - 1"(F) X 1"(F).

Model: LFC - Low Flow Controller

Marking: Floquip, company logo, direction of flow arrow, PN16 & size on body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer:  

Factor: Floquip Valves

WRAS Approval Number  0904319

Print this entry

`T-JUST` range of thermostatic regulating valves which consist of a brass body with thermostatic control elements. The valves are for use in hot water circulating systems to control the temperature of the water. The valve is equipped with a manual or actuated bypass. The purpose of the bypass is to increase the temperature of the water for a certain period of time to control bacterial problems. Maximum working pressure 10 bar.

Size: ½" BSP (Female), ¾" BSP & 1" BSP (Female).

Model: T-JUST A15.I, T-JUST A20.I & T-JUST A25I.K.

Marking: Flowcon, T-JUST, DN, size and direction of flow cast into body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Flowcon International A/S

Factor:  

WRAS Approval Number  1009372

Print this entry

Range of electronic bidet seats with a solenoid valve controlling the flow and discharging via an `AB` air gap. The inlet incorporates a single check valve cartridge. Maximum working pressure 10.0 bar. For use with cold water only.

Size: 3/8" BSP (M)

Model: Geberit AquaClean 5000 & Geberit AquaClean 5000 Plus

Marking: Geberit on front casing. Geberit, Serial number, model number and other technical information on data label on underside of front casing.

Installation Requirements : R001           

Note: This appliance incorporates a Fluid category 5 backflow prevention device.

Proviso:  

Manufacturer: Geberit International AG

Factor: Geberit Sales Limited

WRAS Approval Number  0806315

Print this entry

Range of manifolds (Gunmetal) which incorporate a venturi within the body. The design of the manifold is for operation within a hot water secondary distribution system. The manifold is designed to allow for tappings within the secondary distribution system, which allows water to circulate through the individual circuit and return to the main secondary distribution system. When there is no flow through the individual circuit the venturi within the manifold allows for a continuous flow through the circuit and back to the main secondary distribution system. Maximum working pressure 16.0 bar.

Size: DN15, DN20, DN25 & DN32

Model: Multi Circ Distribution Unit. Art.no. Dimension Threaded Threaded Connector Connector Thread Input output Female Female Female Thread Thread Thread 1210164010015-00 Rp ½" Rp ½" Rp ½" 1210164010020-00 Rp ¾" Rp ½" Rp ½" 1210164010025-00 Rp 1" Rp ½" Rp ½" 1210164010032-00 Rp 1¼" Rp ½" Rp ½" External External External Thread Thread Thread 1210164011015-00 G ¾" B G ¾" G ¾" B 1210164011020-00 G 1" B G ¾" B G ¾" B 1210164011025-00 G 1¼" B G ¾" B G ¾" B 1210164011032-00 G 1½" B G ¾" B G ¾" B External Female Female Thread Thread Thread 1210164012015-00 G ¾" B G ½" G ½" 1210164012020-00 G 1" B G ¾" G ¾" 1210164012025-00 G 1¼" B G ¾" G ¾" 1210164012032-00 G 1½" B G ¾" G ¾" Female Female Female Thread Thread Thread 1210164013020-00 Rp ¾" Rp ¾" Rp ½" 1210164013025-00 Rp 1" Rp ¾" Rp ½" 1210164013032-00 Rp 1¼" Rp ¾" Rp ½" External External External Thread Thread Thread 1210164014020-00 G 1" B G 1" B G ¾" B 1210164014025-00 G 1¼" B G 1" B G ¾" B 1210164014032-00 G 1½" B G 1" B G ¾" B External Female Female Thread Thread Thread 1210164015020-00 G 1" B G 1" G ¾" 1210164015025-00 G 1¼" B G 1" G ¾" 1210164015032-00 G 1½" G 1" G ¾"

Marking: Manufacturers name and logo, PN, DN Arrow showing direction of flows for each circuit cast into body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Gebr Kemper GmbH & Co KG

Factor:  

WRAS Approval Number  1102332

Print this entry

Range of circulation fittings for distribution systems with gun metal bodies, plastic cones & guides and EPDM ‘O’ rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Size: ¾”– 2” BSP ( F )

Model: 12101 650 10 020-00, 12101 650 10 025-00, 12101 650 10 032-00, 12101 650 10 040-00 & 12101 650 10 050-00.

Marking: Manufacturer’s logo, size and direction of flow arrow cast into valve body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Gebr Kemper GmbH & Co KG

Factor:  

WRAS Approval Number  0904320

Print this entry

Multi-Tee-Piece with a Gunmetal body Tee for connecting either sampling or temperature measuring equipment within the water circuit. Maximum working pressure 16 bar & maximum operating temperature 90°C.

Size: DN 15, 20, 32, 40 and 50.

Model: 1280G & 1290G.

Marking: `Kemper` and DN cast into body.

Installation Requirements : R001           

Note:  

Proviso:  

Manufacturer: Gebr Kemper GmbH & Co KG

Factor:  

WRAS Approval Number  1111011

Print this entry

Chromium plated brass 90° wall elbow and plastic cover. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.

Size: ½” BSP male inlet/outlet.

Model: 28.671.

Marking: `Grohe` logo on body of cover.

Installation Requirements : R001