Sealants - Flat Faced Joints

Section 5440

General

WRAS Approval Number 1205531

Cemprotec 2000-BJT. Extruded synthetic rubber sealant strip available in black or grey colours. For use with water up to 23°C.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 1205517

0361 & 0361 water tank sealing strip available in black or grey colours. 0361 is an extruded synthetic rubber sealant strip. 0361 water tank sealing strip is an extruded synthetic rubber sealant strip (water contact part) which is laminated with hard closed-cell PVC foam (not in contact with the water). It is supplied in either an `L` or `U` shaped section. For use with water up to 23°C.

Supplier: HS Butyl Ltd

WRAS Approval Number 1207543

Sikadur 31DW to be used in conjunction with Sika Combiflex SG Membrane. Sikadur 31DW is a grey coloured, two part, site applied epoxy resin adhesive. Sika Combiflex SG Membrane is a grey coloured polyethylene membrane. Parts A & B of the Sikadur 31DW are mixed in a ratio of 3:1 and then brush applied to the Sika Combiflex SG Membrane. Cure for 14 days at 30°C. For use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Supplier: Sika UAE L.L.C

WRAS Approval Number 0812525

`Premcrete Hydroband 2000`. White coloured composite tape. Intended for use as a joint sealing system. For use with water up to 23°C.

Supplier: Premcrete

WRAS Approval Number 1303518

TamAcryl 2000 with corrosion inhibitor. Site applied acrylic grout consisting of Part A (orange coloured liquid), an accelerator (colourless liquid) and Part B (colourless liquid). Mix and apply as per manufacturer`s instructions. The cured product is orange coloured. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Supplier: Normet UK Ltd.

WRAS Approval Number 1208525

UH-2602. Clear, Hot Melt Adesive. Apply as per manufacturer`s instructions, cure for 1 hour at 25°C. For use with water up to 23°C.

Supplier: IFS Industries Inc.

WRAS Approval Number 1210503

Loctite 5800. Black coloured anaerobic adhesive. Apply as per manufacturer`s instructions. Cure for 7 days at an ambient temperature (20 - 23°C). For use with water up to 85°C.

Supplier: Henkel Ltd.

WRAS Approval Number 0807527

Thoroflex 200. Dynamic Joint Waterproofing System consisting of Thoroflex 200 Membrane (Ethylene copolymer membrane strip) & Thoroflex 200 Adhesive (grey coloured, two-part epoxy resin adhesive). Mix the two-part adhesive and apply as per manufacturer`s instructions. Cure 10 days at 7°C. For cold water use only.

Supplier: BASF Construction Chemicals (UK) Ltd

WRAS Approval Number 1109511

MXLOC 38 (green coloured) & MXLOC 48 (green) acrylic based adhesives. Apply as per manufacturer`s instructions. For use with water up to 23°C.

Supplier: Cartell UK Ltd.

WRAS Approval Number 0902508

Bentorub+. Green coloured joint sealant For use only when confined between surfaces. For use only in undertakers service reservoirs and similar structures having been tested at reduced surface area. Cold water use only. Also known as Bentorub Salt and Bentoject.

Supplier: De Neef UK Ltd

WRAS Approval Number 0907531

Swellseal 3V/Swellseal R. Black hydrophilic rubber sealant strip for the sealing of joints in concrete. For cold water use only.

Supplier: De Neef UK Ltd

WRAS Approval Number 0812505

Cemprotec 2000-S. White coloured composite tape. Intended for use as a joint sealing system. Cold water use only.

Supplier: Flexcrete Technologies Ltd

WRAS Approval Number 0808545

Nitoseal MS600 and Fosroc two part Primer MS2. Grey coloured joint sealant. Mix and apply primer as per manufacturers instructions, cure for 4 hours at 7°C. Cure Nitoseal MS600 for 21 days at 7°C. Cold water use only. For use only in undertakers service reservoirs or similar structures having been tested at reduced surface area to volume ratio.

Supplier: Fosroc Ltd

WRAS Approval Number 0904520

FCE Joining Compound. Black coloured magnesium chloride cement. Apply as per manufacturer`s instructions. Cure for 24 hours at 7°C. For hot and cold water use up to 85°C. For use only in undertakers service reservoirs and similar structures having been tested at reduced surface area to volume ratio.

Supplier: Furmanite International Ltd

WRAS Approval Number 0901514

Loctite 770. Transparent polyolefin primer. Cure 0.5 hours at 7°C. For cold water and hot water use up to 85°C.

Supplier: Henkel Ltd.

WRAS Approval Number 0808532

Loctite 648. Translucent green adhesive. Cure 48 hours at 7°C. For use with hot and cold water up to 85°C.

Supplier: Henkel Ltd.

WRAS Approval Number 0910507

Loctite 403. Transparent cyanoacrylate adhesive. Apply as per manufacturers instructions. Cure 24 hours at ambient temperature (22-24°C). For use with cold water only.

Supplier: Henkel Ltd.

WRAS Approval Number 1110527

SB1 Bonding Agent. Black coloured sealant intended to bond plastic to rubber. Apply as per manufacturer`s instructions. For use with water up to 85°C.

Supplier: Superior Seals Ltd